{"id":44782,"date":"2019-03-24T21:01:27","date_gmt":"2019-03-24T12:01:27","guid":{"rendered":"https:\/\/www.decoboco.info\/en\/?p=44782"},"modified":"2026-09-24T13:45:17","modified_gmt":"2026-09-24T04:45:17","slug":"gpz750f-front-maintenance-and-other-repairs","status":"publish","type":"post","link":"https:\/\/www.decoboco.info\/en\/20190324\/everyday-events\/gpz750f-front-maintenance-and-other-repairs","title":{"rendered":"GPZ750F Front maintenance and other repairs"},"content":{"rendered":"
\"\"<\/a><\/div>\n
\"\"

<\/em>

It took some soft damage… so we’re starting with work on the front end.
<\/figcaption><\/figure>\n\n\n\n\n\n\n\n
\"\"
The owner doesn’t even remember when it was last replaced. It had worn in pretty nicely. <\/figcaption><\/figure>\n\n\n\n
\"\"
Next time we open it up… who knows when that’ll be, so we’re giving the inside a good scrub too. <\/figcaption><\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"
The way it went in feels okay, but compared to the entrance, the back feels a bit loose. One more hard hit and it’s basically goodbye. We’re going with this for now. <\/figcaption><\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"
Once the race is installed, we do a quick visual check all the way around. The question of whether it was in there or not disappears, and you can sleep soundly at night. <\/figcaption><\/figure>\n\n\n\n
\"\"
Since it’s a separate handlebar, we’re adding an extra stopper. Back in the day, people would often strip the threads and use bolts and nuts to lock it down.

When you use bolts and nuts as a stopper…
\u2022 There’s no flat surface on the stem stopper side, so the lock nut doesn’t grip well = it loosens easily
\u2022 It’s surprisingly thick and doesn’t allow for flexibility.
And so on.
In recent years, the final consensus has been that welding a plate to the stopper is the fastest and most reliable way.

We’re locking it down to the point where the handlebar lock just barely works. Handlebar locks (steering locks) are checked in inspections these days. Used bikes with customized front ends\u2014watch out!

It sounds simple to say, but…
Leave the old bearing in \u2192 tack weld the thick plate \u2192 check \u2192 grind \u2192 check \u2192 grind \u2192 remove bearing \u2192 mark with a touch pen \u2192 apply oil and press fit. That’s the workflow.

I really think about how much faster and easier it is to service a stock bike…

<\/figcaption><\/figure>\n\n\n\n
\"\"
The usual gate paint\u2014”Asahi Pen Oil-Based High-Durability Iron Parts 83ML”\u2014the small size is really helpful.
If the gate gets wet, it should be fine… <\/figcaption><\/figure>\n\n\n\n
\"\"
The grease is Neutech NC100, as always.
I think the quality of chemicals becomes clear when many people use them for years and tens of thousands of kilometers and you get that “Yeah, it’s reliable” result. This grease is truly trustworthy.
<\/figcaption><\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"
Kawasaki’s characteristic tight seal? has super high friction. It’s a bit outdated, so we remove it and use parts from other bikes.
If you assemble with a seal that grips this tightly, it’ll probably get sloppy pretty quick.

We compress the seal quite a bit, so if someone says “Isn’t the steering really heavy?” we loosen it “somewhat” and reassemble.
At first the seal grips well so play is hard to detect, but after some distance the seal wears out and you get play.
We want to make assembly easy and effective too.

This is just personal experience, so take it as reference. <\/figcaption><\/figure>\n\n\n\n
\"\"
If we have one here, it’s for Suzuki. The outer lip just barely touches the frame outer diameter. The seal center hole just barely touches the adjustment nut protrusion.
This design looks old now too. Honda has been using upper and lower seals for smooth operation for quite a while.
Even HRC manuals have items like “cut the seal lip with a cutter.”

<\/figcaption><\/figure>\n\n\n\n
\"\"
This protrusion must be pressing on the bearing inner race, so be careful when reusing seals. <\/figcaption><\/figure>\n\n\n\n
\"\"
At first you tighten and loosen, let it break in a bit, and if you feel “Is the bearing being pressed firmly?” things move quickly.
Roughly speaking, you adjust between “it won’t tighten any more” and “play starts here.” Then you add the top bridge and tighten the nut, so there’s a lot going on…

I think steering play is easy to confuse with other things.
\u2022 Brake disc pin play
\u2022 Brake pad play (especially if you’ve removed the pad spring)
\u2022 Expansion of the caliper’s pad bore
\u2022 Wear on the upright bottom case (the deep part below center; be a bit careful if there’s no inner metal)
\u2022 Damage from disassembling the inverted inner lower bracket or loosened fit.
\u2022 Loose race press fit on the frame side (sloppy)

For example, if a problem comes up and you can confidently say the stem bearing is fine, you can suspect other things and solve it faster, I think.


<\/figcaption><\/figure>\n\n\n\n
\"\"
Next. The fork is bent, so we’re disassembling three sets including the damaged one and mixing and matching.

<\/figcaption><\/figure>\n\n\n\n
\"\"
It’s been a while since I’ve smelled that sulfur\/hot spring smell. The oil that had turned to sludge\u2014what weight was it? It felt like taking a bath after years. <\/figcaption><\/figure>\n\n\n\n
\"\"
There are places where you have to install a seal and corrosion happens.
The same goes for the snap ring groove. If this is rough and pitted, we don’t force the seal in with “bang bang!” If you don’t remove the corrosion from the snap ring groove, it’ll invite more rust, so be careful. <\/figcaption><\/figure>\n\n\n\n
\"\"
We ground and smoothed the surface. Assemble parts without forcing\u2014do it smartly. That reduces uncertainty and fewer troubles result.
Ideally, a job finishes in one go with no trouble. <\/figcaption><\/figure>\n\n\n\n
\"\"
We hand-polished and corrected the usable inner tube.
The stroke area at the front inevitably gets shiny. The fork moves while tilted, so the fork has it tough too.
When it’s mirror-shiny, there can actually be friction…

By the way, even if plating wears down to sag, it’s in the 100-micron range. The inner tube dimension from top to bottom is also 100-micron range. It’s a long part so some variation shows up.
We thought the leak was because the inner diameter wore down, so we ordered a new OEM inner tube and it was thinner than the used one…
How to avoid damaging the oil seal and keep operation smooth is what matters.

<\/figcaption><\/figure>\n\n\n\n
\"\"
Cleaning the cylinder rod threads. If it’s not held firmly and securely, it causes oil leaks.
A little effort gets you peace of mind. <\/figcaption><\/figure>\n\n\n\n
\"\"
It doesn’t go in this far, but if it threads in by hand, you’re good. You also need to be a bit careful not to over-tap since the other side wears down. <\/figcaption><\/figure>\n\n\n\n
\"\"
Whether it’s due to year or… everything is used so I can’t tell what’s what, but there seem to be differences. <\/figcaption><\/figure>\n\n\n\n
\"\"
Anti-dive fork oil lock\u2014a common thing. <\/figcaption><\/figure>\n\n\n\n
\"\"
This is the reverse pattern. <\/figcaption><\/figure>\n\n\n\n
\"\"
This is the oil lock specification. Well, if it’s not used all the way to full bottom, there’s no problem. But if you do use it all the way to full bottom, the oil lock goes all floppy. <\/figcaption><\/figure>\n\n\n\n
\"\"
I think the top washer is discontinued, so we’re reusing it. Domestic forks are either Kayaba or Showa. Forks have surprising versatility and there are parts you can swap.
I think the GSXR1100 H-J might have been the same…
You could probably build up the backup ring and it’d be fine.
<\/figcaption><\/figure>\n\n\n\n
\"\"
The fork spring is a single-rate from SS Itou.
The spring that was being used was unknown, so we decided to reset it for now. <\/figcaption><\/figure>\n\n\n\n
\"\"
The pressurized fork has a bypass hole, so it’s a bit tricky. We could have welded it shut, but we thought we’d practice on junk first… and if buildup happens on the inside it’d be a pain… so we decided against it.

A weird fork that shows the era. The top cap sinks deep inside the inner tube.
When we first disassembled it, the oil level was super low? Is it because it’s a pressurized fork? But it’s both. <\/figcaption><\/figure>\n\n\n\n
\"\"
Pulling a vacuum feels reassuring. It’s kind of like wiping with paper, then washing, then wiping with paper again… or the reverse? <\/figcaption><\/figure>\n\n\n\n
\"\"
Motion Pro <\/a>
has great design, usability, and pricing\u2014GOOD.

To be continued. <\/figcaption><\/figure>\n","protected":false},"excerpt":{"rendered":"","protected":false},"author":2,"featured_media":44749,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"pochipp_cv_data":"","swell_btn_cv_data":"","footnotes":""},"categories":[1924],"tags":[],"class_list":["post-44782","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-everyday-events"],"_links":{"self":[{"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/posts\/44782","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/comments?post=44782"}],"version-history":[{"count":0,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/posts\/44782\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/media\/44749"}],"wp:attachment":[{"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/media?parent=44782"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/categories?post=44782"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.decoboco.info\/en\/wp-json\/wp\/v2\/tags?post=44782"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}