I’ve been neglecting the blog a bit lately. The chickens’ fault? Ko-ko-ko! ♪ (laugh) Before I knew it, we’re in year-end mode! I’m worrying about sourcing wine and cheese and such… but that’s not what I should be focusing on.
Your beloved bikes, too, have had so much time pass without you noticing that you get hit with “Wait, *that* part is failing?” — unbelievable components reaching the end of their service life. This time it’s speedometer gear damage. I had a hunch it was coming, but it finally hit the limit. The failure of the plastic wire connector typical of this era, and the collapse of the internal sleeve. And since the speedometer gear also serves as the wheel axle collar, it’s not just a dead meter — we needed an urgent fix.
So I researched speedometer gears available for 18-inch wheels across all the makers and uncovered a super useful swap that’ll work going forward! The one I’m using is the Kawasaki Zephyr 1100 unit (OEM part number 41078-1101)! I have a feeling this could be discontinued or go out of stock any time, so if this applies to you, grab a spare while you can
The 17φ axle early-generation GSX-R1100 comes in two types
OEM speedometer gears usable mainly on 18-inch systems break down into three main types when you organize their structure and dimensions.
① Axle diameter 15φ ② Axle diameter 17φ (drive lug outer diameter 47 mm) ③ Axle diameter 17φ (drive lug outer diameter 50 mm)
The target I’m assembling this time is type ② “17φ (47 mm lugs)”! Ideally, keeping future versatility in mind, I’d love to cover both 17φ patterns (47 mm lugs / 50 mm lugs) with matching combinations and collar dimensions, so I’ll keep researching with hands-on testing
The speedometer gear damage this time came down to these two core issues.
① Damage and deformation of the speedometer wire attachment threads (M11 × P1.00), so the wire-side lock nut wouldn’t thread in smoothly. ② Collapse of the center sleeve (collar) inside the gear. Incredibly, it was barely holding the wheel bearing’s inner race (center) — a dangerously marginal situation.
The meter gear isn’t just a box that measures speed; it’s the actual “critical collar that handles rigidity and thrust load when the axle shaft is tightened.” When that collapses, it leads straight to bearing damage and loss of front-end rigidity, so I’m really glad we caught and fixed it at just the right moment
The choice fell on Kawasaki Zephyr 1100 41078-1101
When selecting a replacement meter gear, I focused on these three points!
① The axle diameter must be 17φ ② The overall gear thickness (axle collar length) shouldn’t differ greatly ③ The matching speedometer wire must be easy to source
Narrowing down with these three conditions, the quickest and most logical fit turned out to be the Kawasaki Zephyr 1100 unit.
Of course, this kind of swap work requires solid prep research through parts lists and such, then you hand-order it “just in case” and only get your answer when you line up the actual parts. But if I share the know-how here on the blog once I’ve proven it works, maybe it’ll help save someone else’s bike that’s suffering from the same discontinued or damaged part, right?
Speed wire attachment is M12-1.00 Wire end shape is convex/concave
The oil seal is available as a single part from Kawasaki OEM.
Machine the inner sleeve and outer shell
The oil seal is rock-hard and takes some care to remove without breaking it. It’s not a bad idea to have a replacement oil seal on hand, assuming you might break it.
Machine on the lathe to adjust dimensions. I made a holding fixture, so this will help with future work too.
Machine the receiver too 41064-1006
The receiver side also needs machining to cut the groove. Since it’s a press-stamped part, this side takes more work.
Before machining, I measure the original clearances too.
Made a light press-fit mandrel and clamp to hold it. I didn’t have a large enough round bar, so I couldn’t do two-face holding
First I machined the full width on the lathe, then cut the groove again afterward. It didn’t chatter as much as I expected, so maybe I didn’t need to be quite so rigid?
Straighten the bent lugs and sand them with a belt sander to adjust as needed. It’s a decent length, so I think it’ll work with the 50 mm J-type lugs too.
Sand a bit with the belt sander to adjust as needed. What surprised me was how cleanly the receiver fit into the wheel. If that hadn’t gone in, it would’ve been even more of a hassle.
That’s the speedometer gear machining done. The wire thread diameter changes from M11-1.00 to M12-1.00, so the original wire won’t work. I sourced a Zephyr 1100 unit that’s dimensionally close.
OEM discontinued? Hurricane HB4731 is a bargain!
I sourced the easy-to-find Hurricane HB4731. I was worried when I found out the Kawasaki OEM was discontinued.
It was only about 10 mm longer than the GSX-R1100 OEM. A true Cinderella fit!
Of course, the meter side is to spec, so it bolts right on.
So are all the early oil-cooled 18-inch GSX-R750/1100s in the world saved now?
Zephyr 1100 speedometer gear fitting and road test complete! No interference anywhere, and the operation matched perfectly when I compared it against a GPS meter. It was a customized bike, but this turned out to be a really big win
Best of all, “the gear internals and wire attachment are all metal” — that’s the ultimate peace of mind! For owners running this wheel setup on GSX1100S Katanas and such, this means you can relax about future trouble. Of course, this OEM part won’t be supplied forever either, so it’s wise to stock up before you need it.
One small note, though! This meter gear has no outer flange, so there’s a small gap between it and the wheel hub. A special oil seal size like “outer diameter 55 × inner diameter 47.3 × thickness 5 mm” doesn’t exist in the world, so if the gap bothers you, machine a POM (Delrin) collar or retaineron the lathe and press it in — it’ll look sharper and make wheel removal and installation much easier!